How to Check Timing on Code P0011 Hyundai EQUUS

How tp Check Timing on Code P0011 Hyundai EQUUS

 

2011  G 4.6 DOHC   Engine Control  P0011 \'A\' Camshaft Position-Timing Over-Advanced or System Performance (Bank 1)

Study Monitor GDS Data 1. Study Connect GDS to DLC(Data Link Cable). 2. Study Warm up the engine to normal operating temperature. 3. Study Monitor "CVVT" parameter on GDS. Study the  Normal data of CVVT at idle. 4. Are the parameters displayed correctly ? ▶ Fault is intermittent caused by poor contact in the sensor’s and/or ECM’s connector or was repaired and ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage. Repair or replace as necessary and go to "Verification of vehicle Repair" procedure. ▶ Go to "System Inspection" procedure.

Study Guide System Inspection

■ Visual Inspection

1.	Study Check oil level is O.K.

2.	Study Check oil and OCV is contaminated.

3.	Study Check that any oil leakage is occurred around OCV.

4.	Study a problem been found ? ▶ Repair or replace as necessary and then, go to " Verification of Vehicle Repair" procedure. ▶ Go to "Component Inspection" procedure.
		P0011

Study Guide Component Inspection ■ Check OCV resistance 1. IG "OFF" and disconnect OCV connector. 2. Measure resistance between power and signal terminals of OCV. (Component Side) Specification : 6.7 ~ 7.7 Ω 3. Is the measured resistance within specification? ▶ Go to "Check OCV -Oil Control Valve & Cam phaser" as follows. ▶ Substitute with a known - good OCV and check for proper operation. If the problem is corrected, replace OCV and go to "Verification of Vehicle Repair" procedure. ■ Check OCV -Oil Control Valve & Cam phaser 1. IG "OFF" and connect GDS. 2. ENG "ON" and Measure signal waveform at signal terminal of OCV -Oil Control Valve. 3. Measure signal waveform at signal terminal of Cam phaser. 4. Check the signal waveforms with stepping on accelerator pedal. Specification : Refer to Signal Waveform & Data Study Guide and Auto Repair 5. Is the measured signal waveform O.K ? ▶ Fault is intermittent. Drive the vehicle to meet the enable condition for the DTC. and Go to "Verification of Vehicle Repair" procedure. ▶ Substitute with a known - good CVVT or OCV and check for proper operation. If the problem is corrected, replace CVVT or OCV and go to "Verification of Vehicle Repair" procedure. MMore Description and Auto Repair

How to Check and What is Code P0014 Genesis

2011  G 4.6 DOHC  Engine  Engine Control  P0014 \'B\' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

Component Location General Description Study Guide for The CVVT (Continuously Variable Valve Timing) system is installed to the chain sprocket of the intake camshaft. This system controls the intake camshaft to provide the optimal valve timing for every driving condition. The ECM controls the Oil Control Valve(OCV), based on the signals output from mass air flow, throttle position and engine coolant temperature.Study Guide The CVVT controller regulates the intake camshaft angle using oil pressure through the OCV. As result,Study the relative position between the camshaft and the crankshaft becomes optimal, and the engine torque improves, fuel economy improves, exhaust emissions decrease under overall driving conditions. Study Guide DTC Description If there is a delay between the target angle and the real angle over 5 times,ECM sets DTC P0014. DTC Detecting Condition Study the Item Detecting Condition Possible Cause Study Guide DTC Strategy • Slow response check • Poor connection • Contamination of Oil / Clog of Oil path • OCV • CVVT Study Guide Enable Conditions • Time after | target VVT angle –VVT angle | > 6 deg(2 sec) • Time after engine start > 10 ~ 60 sec • Coolant temperature : 0~120°C • Engine oil temperature : 0~130°C • 1000  rpm  6600rpm Study Guide Threshold value • Counter of delayed following target valve timing > 5 times Diagnosis Time • - MIL On Condition • 2 Driving Cycles Specification OCV Specification Coil Resistance (Ω) 6.7 ~ 7.7 (20°C) More Diagnosis Procedure Study , Study , Study , Study , Study , Study , Study , Study , Study ,

How to repair A/T overdrive not working

How to repair A/T overdrive not working of Hyundai Trajet

Model: Hyundai Trajet

Year Model: 2004

Displacement:2700cc

Fuel: Gasoline

1) Study Condition

1. Automatic Transmission Overdrive switch not working

2) Study the Cause

1. This problem cause of electrical circuit from overdrive switch disconnected.

3) Study and Diagnosis

1. Study and Check with GDS
   = No Trouble Found
2. Study and Check fuse from overdrive circuit = OK
3. Study and Open the Steering column were the shifting lever mounted.
4. Study and Check for the wire of overdrive switch and disconnet.
5. Study and Check the B+
   = no current flows
   = Check for the socket pin, the problem found from the socket only the cover of wire connected to the socket.

4) Study Guide and Repair Procedure

• Repair The disconnected parts

more training and trouble shooting

Study , Study , Study , Study , Study , Study , Study , Study , Study , Study.

How to check output speed sensor code P0722

How to check output speed sensor code P0722

 

P0722 A/T Output speed Sensor Circuit - Open or Short(GND)

Study Guide

Auto Repair

Study Guide and Component Location Study Guide and General Description Study Guide and The Output Speed Sensor outputs pulse-signals according to the revolutions of the output shaft of the transmission. Study Guide and  The Output Speed Sensor is installed in front of the Transfer Drive Gear to determine the Transfer Drive Gear rpms by counting the frequency of the pulses.Study This value, together with the throttle position data, is mainly used to decide the optimum gear position. Study Guide and DTC Description Study The TCM sets this code if the calculated value of the pulse-signal is noticeably different from the value calculated, using the Vehicle Speed Sensor output, when Study the vehicle is running faster than 30 km/h. The TCM will initiate the fail safe function if this code is detected. Study Guide and DTC Detecting Condition Item to Study Detecting Condition and Study Study Possible Cause DTC Strategy ● Speed rationality check ● Signal circuit is open or short. ● Sensor power circuit is open ● Sensor ground circuit is open ● Faulty OUPUT SPEED SENSOR ● Faulty PCM Enable Conditions ● Battery Voltage ≥ 10V ● Lever position : D,3,2,L ● State of brake : OFF Threshold Value ● Output speed = 0 Diagnostic Time ● More than 1sec Fail Safe ● Locked into 3rd or 2nd gear. ● Manual shifting is possibe(2 nd → 3 rd ,3 rd → 2 nd) more cases and  information Study and Study and Study and Study and Study and Study and Study and Study

How input sensor works? code P0717

How input sensor works?code P0717

Model: Hyundai Elantra

Year Model: 2010

Fuel: Gasoline

Displacement: 1600cc

 

Transmission  Automatic Transaxle  P0717 A/T Input speed Sensor Circuit Low Input

Study Guide and Component Location Study Guide and General Description The Study Guide input(turbine) speed sensor outputs waveform signals according to the revolutions of the input shaft ,installed in front of End clutch retainer,of the transmission. The Study Guide TCM determines the input shaft speed by calculating the frequency of the pulses. This Study Guide value is mainly used to control the optimum fluid pressure during shifting. Study Guide and DTC Description The Study Guide PCM/TCM sets this code if an output pulse-signal is not detected, from the input speed sensor, when the vehicle is running faster than 30 km/h. The Study Guide Fail-Safe function will be set by the PCM/TCM if this code is detected. DTC Detecting Condition Item Study Guide Detecting Condition Study Guide Possible Cause Study Guide Study Guide and DTC Strategy ● Speed rationality check ● Signal circuit is open or short. ● Sensor power circuit is open ● Sensor ground circuit is open ● Faulty INPUT SPEED SENSOR ● Faulty PCM/TCM Study Guide Enable Conditions ● Battery Voltage ≥ 10V ● Output speed ≥ 1000rpm ● Engine speed(Only current gear is the 1st gear) ≥ 3000rpm ● Lever position : D,3,2,L Study Guide and Threshold Value ● Input speed = 0 Study Guide and Diagnostic Time ● More than 1sec Fail Safe ● Locked into 3rd or 2nd gear. ● Manual shifting is possibe(2 nd → 3 rd ,3 rd → 2 nd) Study Guide and Specification Input shaft & Output shaft speed sensor ● Type : Hall sensor ● Current consumption : 22mA(MAX) ● sensor body and sensor connector have been unified as one. Study Guide and Schematic Diagram Study Guide and Signal Waveform

more case and study guide

How to Repair Genesis BK Engine Not Starting

How to Repair Genesis BK Engine Not Starting(Full Option)

Model: Genesis(BK)

Year Model: 2010

Fuel: Gasoline

Displacement: 3800cc

A).Study Guide and Auto Repair Condition

1. Engine Not Cranking
   = This a Trouble from Coupe BK that first time encounter, that’s why it is not easy for me to identify where is the trouble occurs but i have a confident that i deed it by the guide of God by using electronic gadget ex.GDS, Scan Tool.

B).Study Guide and Trouble Cause

1. This trouble occurs due to poor contact of Starter relay pin.

C). Study Guide and Trouble Diagnosis

1. Scan tool Check w/ GDS and G-Scan
   =No Trouble found from engine and Transmission.
2. Check for the Key indicator from control panel = OK
3. Check for the light indicator of FOB button switch = OK
4. Check for the fuse of starting system = OK
5. Pull out the starter relay and Check the Positive terminal and Ground terminal = OK
6. Tightened the relay pin then test to start = It works the engine start

D). Auto Repair or Repair Parts

• Check and repair for loose contact from Engine Control Box.
• more case & Study Guide 

Study Guide , Auto Repair , Study Guide , Auto Repair , Study Guide , Auto Repair

How to check code P0011 of Hyundai Equus VI of Chile

How to check code P0011 of Hyundai Equus VI of chile

Model : Hyundai Equus

Year model: 2010

Fuel: Gasoline

Displacement: 4600cc

 

P0011  Camshaft Position-Timing Over-Advanced or System Performance (Bank 1)

Study Guide

Auto Repair

Study Guide and Component Location 2011  G 4.6 DOHC  Engine  Engine Control Auto Repair and Study Guide w/ General Description Study Guide The CVVT (Continuously Variable Valve Timing) system is installed to the chain sprocket of the intake camshaft. Study Guide This system controls the intake camshaft to provide the optimal valve timing for every driving condition. The ECM controls the Oil Control Valve(OCV), based on the signals output from mass air flow, throttle position and engine coolant temperature. The CVVT controller regulates the intake camshaft angle using oil pressure through the OCV. As result, the relative position between the camshaft and the crankshaft becomes optimal, and the engine torque improves, fuel economy improves, exhaust emissions decrease under overall driving conditions. Study Guide and DTC Description If there is a delay between the target angle and the real angle over 5 times,ECM sets DTC P0011. DTC Detecting Condition Study Guide Item Detecting Condition Possible Cause DTC Strategy Study Guide • Slow response check • Poor connection • Contamination of Oil / Clog of Oil path • OCV • CVVT Study Guide Enable Conditions Study Guide • Time after | target VVT angle –VVT angle |  6 deg(2 sec) • Time after engine start  10 ~ 60 sec • Coolant temperature : 0~120°C • Engine oil temperature : 0~130°C • 1000  rpm  6600rpm Threshold value Study Guide • Counter of delayed following target valve timing  5 times Diagnosis Time Study Guide • -Auto Repair and Study Guide MIL On Condition Study Guide • 2 driving cycle Auto Repair and Study Guide w/ Specification OCV Specification Coil Resistance (Ω) 6.7 ~ 7.7 (20°C) Diagnostic Circuit Diagram Signal Waveform & Data Study Guide , Auto Repair , Study Guide , Auto Repair , Study Guide , Auto reapir Fig.1) Normal waveform of OCV & IN-CMPS at idle. Fig.2) Normal waveform of OCV & IN-CMPS at acceleration with load. Study Guide , Auto Repair , Study Guide , Auto Repair , Study Guide , Auto Repair